Search found 1146 matches
- Wed Jul 18, 2018 6:26 pm
- Forum: Early model JD crawler technical support
- Topic: jd440ic cam pump
- Replies: 33
- Views: 21573
Re: jd440ic cam pump
well is a learning experience and not only for me, am sure others on this board appreciate the knowledge that the rest of y'all contribute...mostly it really comes down to the old computer m.o.....kiss...."keep it simple stupid"!!, which obviously i missed!
- Wed Jul 18, 2018 9:48 am
- Forum: Early model JD crawler technical support
- Topic: jd440ic cam pump
- Replies: 33
- Views: 21573
Re: jd440ic cam pump
ok guys..those are the answers that i had anticipated....will edit further i have answer from Lavoy to check out. Pump is ready!!! and second pump needed new gaskets/seals as old hardened. Gonna eliminate that filter in that line will see what it would take to plumb to the return line...it is toward...
- Wed Jul 18, 2018 6:09 am
- Forum: Early model JD crawler technical support
- Topic: jd440ic cam pump
- Replies: 33
- Views: 21573
Re: jd440ic cam pump
ok lets see if Lavoy may have a good suction line? and what cost? what info is needed, overall length? and do away with filter? and other than that i assume the filter should actually be on the pressure line with filter housing mounted stationary and pressure hoses to and from filter. you both menti...
- Tue Jul 17, 2018 6:40 pm
- Forum: Early model JD crawler technical support
- Topic: jd440ic cam pump
- Replies: 33
- Views: 21573
Re: jd440ic cam pump
will get a couple photos and get em posted...will add then here thru edit !! the filter was already added to the suction line...so that begs the question...where did my oil go from the pump? cause the filter was empty and i had filled the pump. see handmade ring by p.o. http://jdcrawlers.lcent.com:8...
- Tue Jul 17, 2018 11:53 am
- Forum: Early model JD crawler technical support
- Topic: jd440ic cam pump
- Replies: 33
- Views: 21573
Re: jd440ic cam pump
ok, so now that Lavoy has my last pump, i have been going over everything can remember about the circumstances /happenings. i checked the pump for pressure again before i took off the suction line, i was not able to get pressure and i had filled the pump and had emptied the oil filter. i then took o...
- Tue Jul 17, 2018 11:19 am
- Forum: Off-topic discussions
- Topic: new website design????
- Replies: 5
- Views: 5784
Re: new website design????
called "stuff happens"??? bad enough when happens to my dozer or other equip.
- Tue Jul 17, 2018 9:45 am
- Forum: Off-topic discussions
- Topic: new website design????
- Replies: 5
- Views: 5784
Re: new website design????
thats what it appears....!!! i just been cruising back to see if get that page again....it was actually a white page and showed a comment by you (something about hope you enjoy etc) and that it was designed by Erika..
- Tue Jul 17, 2018 9:33 am
- Forum: Off-topic discussions
- Topic: new website design????
- Replies: 5
- Views: 5784
new website design????
Tried to pull up this a.m. , and could not!! hmmm....so went and mowed lawn a bit....come back and pull up jdcrawler site and appears a new initial screen and i like it...tis simple and clear...dont know if upgraded today or when so if i have been missing your new improvements its simply cause i pul...
- Wed Jul 11, 2018 9:42 am
- Forum: Early model JD crawler technical support
- Topic: jd440ic charging issues & hyd cyl issues
- Replies: 103
- Views: 58550
Re: jd440ic charging issues & hyd cyl issues
ok...so after getting set to take pump off again i disconnected the suction line at the pump and the fitting comes off the end....so looking at it consists of sleeve with flat o ring type rubber seals on it....so i take entire suction pipe off at tank and it also has same fittings..close inspection ...
- Tue Jul 10, 2018 7:50 am
- Forum: Early model JD crawler technical support
- Topic: jd440ic charging issues & hyd cyl issues
- Replies: 103
- Views: 58550
Re: jd440ic charging issues & hyd cyl issues
JimB, Thanks for confirmation of my thinking...i did check with shop to see what cost was to inspect/test the vickers...est 1hr for cost of $125, so that will wait too!! considering that everything basically remains the same as when i tok my pump off, i will wait and test again when i get my rebuilt...
- Mon Jul 09, 2018 8:36 am
- Forum: Early model JD crawler technical support
- Topic: jd440ic charging issues & hyd cyl issues
- Replies: 103
- Views: 58550
Re: jd440ic charging issues & hyd cyl issues
ok so while waiting for rebuilt pump....my "new" pump was replaced with claims to be a working pump off another dozer to replace my new pump...now that aint working so considering what issues may else be causing problems.. i decided to dig a bit and have taken off the hose running from top of tank t...
- Mon Jul 09, 2018 7:06 am
- Forum: Late model JD crawler technical support
- Topic: Final drive
- Replies: 5
- Views: 4399
Re: Final drive
my jd440ic final drives simply showed a thin coating of paint
edit
mine are dry so JimB sounds right, but sure others will advise further
edit
mine are dry so JimB sounds right, but sure others will advise further
- Sat Jul 07, 2018 6:30 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: jd440 parts available for sale
- Replies: 9
- Views: 9786
Re: jd440 parts available for sale
well hope someone needs the blamed thing ...i don't
- Fri Jul 06, 2018 11:20 am
- Forum: Late model JD crawler technical support
- Topic: 450c Ripper Mounts
- Replies: 8
- Views: 6153
Re: 450c Ripper Mounts
good job! and thanks!
- Fri Jul 06, 2018 8:32 am
- Forum: Late model JD crawler technical support
- Topic: 450c Ripper Mounts
- Replies: 8
- Views: 6153
Re: 450c Ripper Mounts
can't see your code, but see you trying to get full size pic.....what happened at my end when i open pic it wont move back to crawlers site...try to edit your code and put..normal_ like shown in examples.directly before the pic file number..that will put pic right in your post and be able to stay in...