Search found 382 matches
- Sat Sep 14, 2013 5:45 am
- Forum: Late model JD crawler technical support
- Topic: Won't turn over.......
- Replies: 7
- Views: 9538
check any neutral safety switches .... see if you have start signal to the starter solenoid if you do then see if you have good contact on the main cable if so replace the solenoid 2nd that. Move the shift lever back and forth across the neutral position while keeping the start button pushed. On my...
- Sat Sep 07, 2013 6:42 am
- Forum: Late model JD crawler technical support
- Topic: New guy with a 450b
- Replies: 18
- Views: 13869
- Fri Sep 06, 2013 6:31 am
- Forum: Late model JD crawler technical support
- Topic: New guy with a 450b
- Replies: 18
- Views: 13869
When you say the oil dumped out, was that immediately? Like as fast as you poured it in, it was running out? On my machine the both of the lines running from the pump have been replaces with hoses. I also had the added bonus of them using a galvanized street ell for one of the fittings. If the oil i...
- Tue Aug 27, 2013 8:43 am
- Forum: Late model JD crawler technical support
- Topic: 79 JD 450c track tensioner adjustment?
- Replies: 7
- Views: 7979
- Tue Aug 27, 2013 8:34 am
- Forum: Late model JD crawler technical support
- Topic: straight 450 oil in clutch housing
- Replies: 44
- Views: 41780
- Mon Aug 26, 2013 6:12 am
- Forum: Late model JD crawler technical support
- Topic: How do you grease the lower idlers 350c
- Replies: 21
- Views: 20026
the oil type gun will NOT take cartridges it has a tight seal in the tube that wont go in the cartridge i am not sure that the oil/low pressure gun will work with corn head grease ( maybe some of the others here have used corn head in a low pressure gun???) i use 140WT in mine and it works great bu...
- Sun Aug 25, 2013 6:22 am
- Forum: Late model JD crawler technical support
- Topic: How do you grease the lower idlers 350c
- Replies: 21
- Views: 20026
it is 1800 psi but it is not the pressure it is the fact that you can FEEL when the rollers are full with a reg. grease gun you cant FEEL it and they dont hold oil very well. the roller seals wont take more than a few psi. i would bet so a gauge on a reg. gun wont do you any good ..... i have one o...
- Fri Aug 16, 2013 7:03 am
- Forum: Off-topic discussions
- Topic: water pump rebuild kits
- Replies: 5
- Views: 6709
- Wed Aug 14, 2013 7:53 am
- Forum: Off-topic discussions
- Topic: water pump rebuild kits
- Replies: 5
- Views: 6709
There should have been a seal in it like jtrichard says or that was the first problem I had a service man crush the plastic bushing when installing the shaft not once but twice .We now do this job our selves But what I like about Deere water pumps is you can rebuild them over and over again .I woul...
- Tue Aug 13, 2013 6:47 pm
- Forum: Late model JD crawler technical support
- Topic: Upper Radiator mounts
- Replies: 0
- Views: 1564
Upper Radiator mounts
I got some new upper radiator mounts as mine were trash. There is a long side and a short side, which side goes towards the radiator bracket? Also, what size pop rivet do I need?
Thanks
Thanks
- Mon Aug 12, 2013 7:34 am
- Forum: Late model JD crawler technical support
- Topic: 350c Won't Stay Running - Please Help.
- Replies: 6
- Views: 5749
it was my understanding that if it ran good with the return valve removed then the head was most likely ok? i thought another post on here said that but maybe i read it wrong. By what you are posting I would say your head is good. The items you are going to need are; Seal Kit 24371, $14.62 Pilot tu...
- Sun Aug 11, 2013 8:15 am
- Forum: Late model JD crawler technical support
- Topic: 450C Loader Trans Temp Sensor Location
- Replies: 10
- Views: 9467
sounds like its toast ... you just have to be good and fast and you can change it with out much oil loss Understood.. I'm not running the machine that hard right now. I've been running down hydraulic leaks right now and I may have to pull the belly pan at some point. Just fixed one major leak point...
- Sun Aug 11, 2013 7:55 am
- Forum: Late model JD crawler technical support
- Topic: 350c Won't Stay Running - Please Help.
- Replies: 6
- Views: 5749
sounds like the pump ... search "mouse turds" it will tell you what you most likely have I agree. The same thing happened to me. Bought the machine, got it home and after about 5 hours mine exhibited the same exact behavior. Did the research bought the parts and repaired the pump. I believe when it...
- Sat Aug 10, 2013 2:59 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Loader Trans Temp Sensor Location
- Replies: 10
- Views: 9467
- Sat Aug 10, 2013 6:22 am
- Forum: Late model JD crawler technical support
- Topic: 450C Loader Trans Temp Sensor Location
- Replies: 10
- Views: 9467
I have found the senor, thanks all. I believe I'm going to wait until I do a transmission oil change before I replace the sensor. I have had thoughts of putting the sensor up by the filter ahead of the cooler since its easier to get at and the wire would be less likely to be ripped off by debris. An...