Search found 10807 matches

by Lavoy
Wed Dec 27, 2006 4:47 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: MC1 plow for tool carrier for sale
Replies: 3
Views: 4186

It fits all three, the mounts are the same.
Lavoy
by Lavoy
Wed Dec 27, 2006 4:46 pm
Forum: Early model JD crawler technical support
Topic: MC rollers
Replies: 5
Views: 6028

I doubt you could get them machined for $500 each unless you took some awful large quantities. If you are not concerned about original, I have some NOS Berco roller shells that should adapt fairly easily. Thay are square bored and should accept sealed bearings quite easily. I have been going to make...
by Lavoy
Wed Dec 27, 2006 11:19 am
Forum: Lavoy's Little Shop O' Deeres
Topic: Rubber track pads for sale
Replies: 5
Views: 7064

They did, but finging a useable set will be almost impossible. I have the cup portions of a set, but they would have to have new rubber molded on them.
Lavoy
by Lavoy
Wed Dec 27, 2006 11:18 am
Forum: Early model JD crawler technical support
Topic: GEARMATIC WINCH PARTS FOR MODEL 8A.
Replies: 12
Views: 12732

Paccar may give or sell you one, just contact them to see.
If your pistons are that frozen, you will need complete pistons then?
Lavoy
by Lavoy
Wed Dec 27, 2006 11:17 am
Forum: Early model JD crawler technical support
Topic: 440 final ?????
Replies: 4
Views: 4768

Yes you can if they are the same final, all you will have to do is move the drawbar dowels.
Lavoy
by Lavoy
Tue Dec 26, 2006 8:06 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: Rubber track pads for sale
Replies: 5
Views: 7064

They do not fit MC, and will not fit 440 unless it has 4 bolt rails.
Lavoy
by Lavoy
Tue Dec 26, 2006 8:04 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: for sale: reverser and transmission for 1010
Replies: 3
Views: 4731

No, 1010 is a completely different setup.
Lavoy
by Lavoy
Tue Dec 26, 2006 8:03 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: MC roller assemby
Replies: 1
Views: 3406

Rollers and idlers for MC are getting little hard to come by. I have some front idler brackets, nothing left for rollers, but they can be found.
Lavoy
by Lavoy
Tue Dec 26, 2006 8:01 pm
Forum: Early model JD crawler technical support
Topic: GEARMATIC WINCH PARTS FOR MODEL 8A.
Replies: 12
Views: 12732

Vic,
I have some of the cylinder parts, should be able to get more, but have not tried for sure.
Only manual availalbe would be parts manual.
Lavoy
by Lavoy
Tue Dec 26, 2006 10:49 am
Forum: Early model JD crawler technical support
Topic: Starting my 44o0
Replies: 11
Views: 9689

Is it gas or diesel? Did you buy a battery with enough cold cranking amps? Did you reuse the old cables and ends, or replace them?
Lavoy
by Lavoy
Sun Dec 24, 2006 7:15 pm
Forum: Late model JD crawler technical support
Topic: 350 transmission
Replies: 1
Views: 4518

If you are working on any of the trans shafts, really no way to do much of anything without both finals off, and the ring gear and carrier out of the way.
Check on E-bay, there are usually some manuals on there, or they are current from Deere, at least in CD format.
Lavoy
by Lavoy
Sun Dec 24, 2006 7:13 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: New items in for sale
Replies: 8
Views: 8802

Steve,
Send me an e-mail and we will get the particulars taken care of.
Lavoy
by Lavoy
Sun Dec 24, 2006 7:10 pm
Forum: Early model JD crawler technical support
Topic: Merry Christmas
Replies: 5
Views: 5836

Happy holidays to everyone, hope you have enjoyed the board this last year, looking forward to next.
Lavoy
by Lavoy
Sun Dec 24, 2006 7:09 pm
Forum: Early model JD crawler technical support
Topic: My 40 crawler
Replies: 3
Views: 4143

Stan,
Yes, just send me the shaft, $135 should cover shaft and freight. Be sure to put a note in there with the return shipping address you want.
Lavoy Wilcox
7716 70th St S
Horace, ND 58047
by Lavoy
Sat Dec 23, 2006 10:01 pm
Forum: Late model JD crawler technical support
Topic: 350 steering assembly
Replies: 1
Views: 4441

Fingers are adjusted with a clutch finger gauge, I have them for $15.
Lavoy