Search found 362 matches
- Thu May 19, 2016 4:46 pm
- Forum: Early model JD crawler technical support
- Topic: Damaged spline on axle shaft of the 420
- Replies: 10
- Views: 14823
- Thu May 19, 2016 1:22 pm
- Forum: Early model JD crawler technical support
- Topic: Damaged spline on axle shaft of the 420
- Replies: 10
- Views: 14823
- Thu May 19, 2016 9:48 am
- Forum: Early model JD crawler technical support
- Topic: Damaged spline on axle shaft of the 420
- Replies: 10
- Views: 14823
New addition to an old thread. I saw that a guy on eBay was selling 2 pound kits of Devcon Titanium Epoxy Putty for $100 plus $20 shipping, a little over half the normal price. My understanding is that it last on the shelf for a good deal of time, so I thought I would buy this larger kit to try.. I ...
- Thu Aug 13, 2015 8:27 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 440icd on ebay in tennesee at only 2G
- Replies: 4
- Views: 5601
- Thu Jul 03, 2014 4:56 am
- Forum: Early model JD crawler technical support
- Topic: 440 tranny
- Replies: 12
- Views: 9680
The "small" versus "big" transmission: JD440 Serial # 440001 – 448000 M4256T “small” transmission used on earlier crawlers. Has a fill plug on the right hand side of the case. Has no top cover plate under the seat on top of the housing. JD440 Serial # 448001 up (diesel introduced) T11396 “big” trans...
- Thu Jul 03, 2014 4:44 am
- Forum: Early model JD crawler technical support
- Topic: Jd 1010 blade
- Replies: 5
- Views: 5895
This is a list of the John Deere blades as I far as I have been able to compile them. I will try to find a better way to display the data since I do not know how to embed a table or enter tabs on the website. The first "column" is the blade model number. The second is the crawler it came on. The thi...
- Wed Jul 02, 2014 7:58 pm
- Forum: Early model JD crawler technical support
- Topic: 440 hydraulic tensioners
- Replies: 3
- Views: 3771
Hydraulic tensioners are not covered in any version of the JD440 Service Manual. Probably were covered in a Bulletin. The parts are in the Parts Manual however. The inside of the tube can have a scratch or a gouge in it to allow grease to pass. Was it doing this before? Sounds like the new seal may ...
- Wed Jul 02, 2014 7:47 pm
- Forum: Early model JD crawler technical support
- Topic: 440 tranny
- Replies: 12
- Views: 9680
I have pulled a transmission out the rear before (I had the final drives off). My moment of concern was pitting it back in when I wondered if it would line up properly going over the hump and not damage a bearing or seal. But being an old Harley rider, I did not force it, I just used a bigger hammer...
- Wed Jul 02, 2014 7:34 pm
- Forum: Early model JD crawler technical support
- Topic: What set if tracks to put back on my 440?
- Replies: 26
- Views: 20626
Like PaPa always said about corn... "Knee high by the fourth of July." I have a similar problem trying to pick the best tracks from a pile of not so perfect options. In my case I need 12 inch pads to use with an inside mount dozer blade. All my dozer pads are 14 inch, so I am considering using a goo...
- Wed Jul 02, 2014 7:09 pm
- Forum: Early model JD crawler technical support
- Topic: JD 440 blade
- Replies: 2
- Views: 3249
- Tue Mar 11, 2014 7:10 am
- Forum: Early model JD crawler technical support
- Topic: Reverser Only Works In Reverse
- Replies: 5
- Views: 4749
- Sun Feb 02, 2014 6:59 am
- Forum: Early model JD crawler technical support
- Topic: 420 running issues, spark, battery, points?
- Replies: 49
- Views: 32116
- Sat Feb 01, 2014 7:41 pm
- Forum: Early model JD crawler technical support
- Topic: GearMatic 8A vs. 8G Winch -- Which to Use? -- Good vs. Bad??
- Replies: 6
- Views: 6466
- Sat Feb 01, 2014 7:32 pm
- Forum: Early model JD crawler technical support
- Topic: 420 running issues, spark, battery, points?
- Replies: 49
- Views: 32116
Dollar bills are made out of extremely high quality linen paper. It leaves no lint and will not tear easily. Make sure your distributor is free of moisture. Remove the points plate and clean underneath it. Also look closely at the insulator around the wire coming into the distributor. Look at all th...
- Sat Feb 01, 2014 7:16 pm
- Forum: Early model JD crawler technical support
- Topic: no power to left track
- Replies: 5
- Views: 5091