hydraulics
hydraulics
Hi everyone, good day to you all, I am experiencing a slow lowering of my loader when raised and engine off. could a low fluids level cause this or am I looking for a bad seal? Can't see fluid dripping any where, maybe internal ? Also my service manual says when changing same fluid to replace with S.A.E 5W- 20 oil, not hydraulic fluid? Is this correct or a misprint in my manual?
- Stan Disbrow
- 350 crawler
- Posts: 2898
- Joined: Fri Jul 15, 2005 3:13 pm
- Location: Raleigh, NC
Hi,
If you can't see a leak, probably seeping back thru the control valve. Your manual is printed correctly for when it was new. These days, use a decent hydraulic oil. They have additives which you want, which didn't exist back then.
Stan
If you can't see a leak, probably seeping back thru the control valve. Your manual is printed correctly for when it was new. These days, use a decent hydraulic oil. They have additives which you want, which didn't exist back then.
Stan
There's No Such Thing As A Cheap Crawler!
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
hey shugy, i figured you'd be busy fighting fire,,that guy Scott is a fireman down there..he is just on the south edge of it.(or was)
to answer your question, one of your spool valves probably needs to be pulled, it may just have slug/debris in the spool.
very easily checked. you may notice an o-ring or 2 needing replaced.
figure out which lever lowers it and pull out that spool.
of course engine off with no pressures.
to answer your question, one of your spool valves probably needs to be pulled, it may just have slug/debris in the spool.
very easily checked. you may notice an o-ring or 2 needing replaced.
figure out which lever lowers it and pull out that spool.
of course engine off with no pressures.
440icd/602/8a,,440icd/831/ripper,,440icd/831/3pt.,misc. 440 parts, i have 5 of these now, but i can stop anytime
hydraulics
thanks Stan I was a little confused by that, and pop pop I don't see any reference to a " spool " in my service manual. Can you clarify a little more? Thanks. and I am not a fireman but my son rides along in the cal fire helo as a paramedic.
Most likely the piston cups are leaking by .... Since your book says OIL I have to assume we are talking 440 or before?...... A spool is the rod/shaft/piston in your control valve they CAN wear and leak by but I would lean more the piston seal in the lift cylinders
2010 with 622 dozer with mod. 35 ripper and a 2010 with 622 dozer bought in 1969 and a 2010 loader with drott and mod. 36 ripper
- Stan Disbrow
- 350 crawler
- Posts: 2898
- Joined: Fri Jul 15, 2005 3:13 pm
- Location: Raleigh, NC
Hi,
The control valve pistons look a lot like thread spools, which is where I think they got their name from.
On the earlier machines, they have adjustable rods between the valve pistons and the lever. So the issue may well be with that. You could tell by just how much lever action is needed before it drops.
And, yes, it might be the piston seals in the cylinder(s). You didn't say which machine and blade, so you might have only one....
Stan
The control valve pistons look a lot like thread spools, which is where I think they got their name from.
On the earlier machines, they have adjustable rods between the valve pistons and the lever. So the issue may well be with that. You could tell by just how much lever action is needed before it drops.
And, yes, it might be the piston seals in the cylinder(s). You didn't say which machine and blade, so you might have only one....
Stan
There's No Such Thing As A Cheap Crawler!
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
hydraulics
Once again I asked for the ingredients without letting you all know the main dish I have 1956 JD- L 420-C with a Hydreco monoblock double valve which operates the four rams needed for the loader
Who is online
Users browsing this forum: No registered users and 118 guests