440icd tracks
-
- MC crawler
- Posts: 5
- Joined: Tue Mar 30, 2021 7:22 pm
- Location: Ohio
440icd tracks
I’m working on getting my grandpas 440icd going but the tracks are shot. They’re worn through the bushings and into the pins. Does anyone know where I could find a new or less used set of tracks?
Re: 440icd tracks
Nothing new avaialable other than conversion to 350 or Mitsubishi.
If your link height is okay, they just need to be rebushed, unfortunately no pins and bushings right now, but I am working on it.
lavoy
If your link height is okay, they just need to be rebushed, unfortunately no pins and bushings right now, but I am working on it.
lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator www.jdcrawlers.com
Owner and moderator www.jdcrawlers.com
Re: 440icd tracks
Nothing new avaialable other than conversion to 350 or Mitsubishi.
If your link height is okay, they just need to be rebushed, unfortunately no pins and bushings right now, but I am working on it.
lavoy
If your link height is okay, they just need to be rebushed, unfortunately no pins and bushings right now, but I am working on it.
lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator www.jdcrawlers.com
Owner and moderator www.jdcrawlers.com
-
- MC crawler
- Posts: 5
- Joined: Tue Mar 30, 2021 7:22 pm
- Location: Ohio
Re: 440icd tracks
I read that the sprocket has to be rerimmed to run 350 tracks. How would I go about this? Or would I need to given the sprockets have some wear as well.
- Stan Disbrow
- 350 crawler
- Posts: 2898
- Joined: Fri Jul 15, 2005 3:13 pm
- Location: Raleigh, NC
Re: 440icd tracks
Hi,
A machine shop can cut your old teeth off the sprockets leaving a hub to weld or bolt the new rim onto.
Stan
A machine shop can cut your old teeth off the sprockets leaving a hub to weld or bolt the new rim onto.
Stan
There's No Such Thing As A Cheap Crawler!
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
Re: 440icd tracks
Correct, it will have to be rerimmed to run either 350 or Mitsubishi tracks. You will need a 350 sprocket to cut the rim off of, cut the rim off of your sprocket, and weld the 350 rim back on.
The question is what do you mean by shot? Pads are shot, pins and bushings are shot, links are shot, etc.
Lavoy
The question is what do you mean by shot? Pads are shot, pins and bushings are shot, links are shot, etc.
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator www.jdcrawlers.com
Owner and moderator www.jdcrawlers.com
-
- MC crawler
- Posts: 5
- Joined: Tue Mar 30, 2021 7:22 pm
- Location: Ohio
Re: 440icd tracks
The bushings are worn clear through. I can see the pin inside. I’m assuming the pins are also worn out if the bushings have made it that far. I haven’t measured the links. The pads aren’t bad. I just tore the right final drive apart to rebuild it and found the tapered splines on the bull gear are chipped and worn bad so I’m gonna have to find another gear.
-
- MC crawler
- Posts: 5
- Joined: Tue Mar 30, 2021 7:22 pm
- Location: Ohio
Re: 440icd tracks
What does it take to switch to Mitsubishi tracks?
Re: 440icd tracks
Basically the same as switching to 350 tracks. You need new Mitsubishi sprockets to cut the rims from. The Mitsubishi rims get welded to your sprockets after the rims are cut off your current sprockets. his post will give you a better idea. Pretty much the same for regular tracks with steel pads/grousers.
viewtopic.php?t=4390
viewtopic.php?t=4390
Re: 440icd tracks
Price is basically the same, in the $4000-$5000 range by the time you are done.
Lavoy
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator www.jdcrawlers.com
Owner and moderator www.jdcrawlers.com
-
- 2010 crawler
- Posts: 597
- Joined: Thu Aug 27, 2009 10:08 pm
- Location: Edmonton, Alberta
Re: 440icd tracks
Best to go deere as new and used are available. Last guy I know that did this drilled his 2 bolt pads to 4 bolt (using our jig) which saved him from buying pads.
Jason Benesch
John Deere 420, 430, 440 & 350C With 3 Point Hitch
John Deere 400G With Winch
John Deere 2010 Crawler Dozer
John Deere 420, 430, 435 & 440 Wheel Tractors
John Deere 420, 430, 440 & 350C With 3 Point Hitch
John Deere 400G With Winch
John Deere 2010 Crawler Dozer
John Deere 420, 430, 435 & 440 Wheel Tractors
Who is online
Users browsing this forum: gaspumpsam, Hurlbutt and 106 guests