420 carb flooding?
420 carb flooding?
Any ideas why carb is getting a steady flow of fuel? Fuel coming out of breather tube at carb.
- JD440ICD2006
- 350 crawler
- Posts: 1113
- Joined: Tue Aug 22, 2006 3:57 pm
- Location: South Carolina
The float inside the bowl opens and closes a needle valve that controls the amount of fuel in the bowl at any given time. It can be a bad needle valve, a bad needle valve seat, or the float not adjusted correctly.
A new needle and seat are included in most carb rebuild kits.
A new needle and seat are included in most carb rebuild kits.
1959 JD 440ICD w/64 Power Angle Tilt Blade
1959 JD 440ICD w/63 Manual Angle Blade
1959 JD 440IC w/602 Manual Angle Blade
1959 JD 730D W SE (many options)
1950 JD M S w/M-20 Mower
1952 JD M W
1955 FORD 640 (burns the most fuel)
1959 JD 440ICD w/63 Manual Angle Blade
1959 JD 440IC w/602 Manual Angle Blade
1959 JD 730D W SE (many options)
1950 JD M S w/M-20 Mower
1952 JD M W
1955 FORD 640 (burns the most fuel)
- Stan Disbrow
- 350 crawler
- Posts: 2904
- Joined: Fri Jul 15, 2005 3:13 pm
- Location: Raleigh, NC
Hi,
Usually this turns out to be a piece of dirt stuck in the needle valve. That means a manual cleaning.
There's supposed to be a screen inside the carb inlet, part of the elbow that the fuel line attaches to. They get clogged, and I've seen a lot where someone just snipped off that screen as a result.
So, now the dirt it used to trap gets to the needle valve and - stick city with gas wandering out of the air intake.....
Later!
Stan
Usually this turns out to be a piece of dirt stuck in the needle valve. That means a manual cleaning.
There's supposed to be a screen inside the carb inlet, part of the elbow that the fuel line attaches to. They get clogged, and I've seen a lot where someone just snipped off that screen as a result.
So, now the dirt it used to trap gets to the needle valve and - stick city with gas wandering out of the air intake.....
Later!
Stan
There's No Such Thing As A Cheap Crawler!
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
- Paul Buhler
- 350 crawler
- Posts: 991
- Joined: Wed May 21, 2008 6:25 pm
- Location: Killington, VT
- Paul Buhler
- 350 crawler
- Posts: 991
- Joined: Wed May 21, 2008 6:25 pm
- Location: Killington, VT
whoops, use pm or send to: pbuhler@vermontel.net.
Paul Buhler
Killington, VT
420c 5 roll with 62 blade, FOPS, and Gearmatic 8a winch
Killington, VT
420c 5 roll with 62 blade, FOPS, and Gearmatic 8a winch
Who is online
Users browsing this forum: No registered users and 83 guests