Show us pictures of your JD crawler and attachments.
-
jtrichard
- 350 crawler
![350 crawler 350 crawler](./images/ranks/wrench/spanner_rank_5.gif)
- Posts: 1883
- Joined: Sun Jan 11, 2009 9:48 pm
- Location: Joshua Tree CA
Post
by jtrichard » Sun Dec 09, 2012 5:49 pm
raised seat i am 6'4"
custom built alternator brackets tucked in nice and tight
seat lift and hand made battery hold down
760 deere in back ground
co-pilot
note scaring on rear of ripper cylinders some jerk in the past had used them as a push block when i rebuilt them i had to put in press and get them as round as possible then honed the crap out of them to get the pistons back in as you can see i need a few more shanks any one got some?
made new rear spring cover
![Image](http://i1337.photobucket.com/albums/o665/presref1/tractorsandpuppies025.jpg)
Last edited by
jtrichard on Tue Aug 05, 2014 8:27 pm, edited 6 times in total.
2010 with 622 dozer with mod. 35 ripper and a 2010 with 622 dozer bought in 1969 and a 2010 loader with drott and mod. 36 ripper
-
Lavoy
- Site Admin
![Site Admin Site Admin](./images/ranks/wrench/spanner_rank_5_admin.gif)
- Posts: 10957
- Joined: Sun Apr 03, 2005 8:32 pm
- Location: North Dakota
-
Contact:
Post
by Lavoy » Sun Dec 09, 2012 6:11 pm
That would be a handy rig.
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator
www.jdcrawlers.com
-
jtrichard
- 350 crawler
![350 crawler 350 crawler](./images/ranks/wrench/spanner_rank_5.gif)
- Posts: 1883
- Joined: Sun Jan 11, 2009 9:48 pm
- Location: Joshua Tree CA
Post
by jtrichard » Sun Dec 09, 2012 6:25 pm
thank you Lavoy it is very handy
any idea what this starter is off of from what i can figure out its off of a 3010 ever seen that before?
![Image](http://i1337.photobucket.com/albums/o665/presref1/tractorsandpuppies022.jpg)
2010 with 622 dozer with mod. 35 ripper and a 2010 with 622 dozer bought in 1969 and a 2010 loader with drott and mod. 36 ripper
-
Lavoy
- Site Admin
![Site Admin Site Admin](./images/ranks/wrench/spanner_rank_5_admin.gif)
- Posts: 10957
- Joined: Sun Apr 03, 2005 8:32 pm
- Location: North Dakota
-
Contact:
Post
by Lavoy » Sun Dec 09, 2012 6:53 pm
Nothing I recognize from the pic. I know on the 1010 at one time there was a replacment rebuilt starter available from Wilson that was a different style.
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator
www.jdcrawlers.com
-
jtrichard
- 350 crawler
![350 crawler 350 crawler](./images/ranks/wrench/spanner_rank_5.gif)
- Posts: 1883
- Joined: Sun Jan 11, 2009 9:48 pm
- Location: Joshua Tree CA
Post
by jtrichard » Sun Dec 09, 2012 7:17 pm
it has 3 bolt holes only two used on 2010 fits perfect kinda nice with the solenoid on top looking at pics of 3010 3020 4010 and 4020 looks like its one of them and also i have the side covers for this machine just not on right now
2010 with 622 dozer with mod. 35 ripper and a 2010 with 622 dozer bought in 1969 and a 2010 loader with drott and mod. 36 ripper
-
Lavoy
- Site Admin
![Site Admin Site Admin](./images/ranks/wrench/spanner_rank_5_admin.gif)
- Posts: 10957
- Joined: Sun Apr 03, 2005 8:32 pm
- Location: North Dakota
-
Contact:
Post
by Lavoy » Mon Dec 10, 2012 9:12 am
That could be, been a while since I pulled a starter on a 4020, but I know there is one bolt on the backside that can be a bugger.
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator
www.jdcrawlers.com
-
digitup2
- 350 crawler
![350 crawler 350 crawler](./images/ranks/wrench/spanner_rank_5.gif)
- Posts: 858
- Joined: Tue Feb 05, 2008 6:36 pm
Post
by digitup2 » Mon Dec 10, 2012 12:03 pm
We put a 3010-3020 starter on the 450B one time and never looked back in the cold weather they started every time no fooling around with a smaller starter we even up graded the 550s and 550A's & 550B's to that starter didn't need any ether till it was dam cold that was our first up grade to any dozer when we got them .The bigger starter turns that little motor over so much faster that starter is worth the extra bucks .And there is actually just enough room for it too .Digitup.
-
jtrichard
- 350 crawler
![350 crawler 350 crawler](./images/ranks/wrench/spanner_rank_5.gif)
- Posts: 1883
- Joined: Sun Jan 11, 2009 9:48 pm
- Location: Joshua Tree CA
Post
by jtrichard » Mon Dec 10, 2012 10:46 pm
i can get new ones but they are about $130 found the retainers on ebay so i have 5 or 6 of them
2010 with 622 dozer with mod. 35 ripper and a 2010 with 622 dozer bought in 1969 and a 2010 loader with drott and mod. 36 ripper
-
05victorylly
- 430 crawler
![430 crawler 430 crawler](./images/ranks/wrench/spanner_rank_1.gif)
- Posts: 62
- Joined: Sat Nov 10, 2012 6:14 pm
- Location: Western MA
Post
by 05victorylly » Mon Dec 10, 2012 11:34 pm
Really wish my loader had a 4-1 bucket! Would be great for all the rocks I have to move.
IH 500 6-day dozer , JD 2010 track loader, Ford 1900 4x4
-
gregjo1948
- 350 crawler
![350 crawler 350 crawler](./images/ranks/wrench/spanner_rank_5.gif)
- Posts: 1000
- Joined: Mon Aug 30, 2010 5:58 am
- Location: Newark Valley,NY,USA
Post
by gregjo1948 » Tue Apr 15, 2014 5:49 am
Looks like a fun machine to play with! gregjo1948
JD 350B diesel 6way blade, Case 580B Loader/backhoe, Farmall 504 high crop w/ flail boom mower, International 404 , International 284 diesel w/belly mower, 1972 Ford F600 dump truck, Galion 3-5 roller, Allis Chalmers D17, 1620 Ford
-
jtrichard
- 350 crawler
![350 crawler 350 crawler](./images/ranks/wrench/spanner_rank_5.gif)
- Posts: 1883
- Joined: Sun Jan 11, 2009 9:48 pm
- Location: Joshua Tree CA
Post
by jtrichard » Tue Aug 05, 2014 8:26 pm
oh it is ....putting hoe on it soon
2010 with 622 dozer with mod. 35 ripper and a 2010 with 622 dozer bought in 1969 and a 2010 loader with drott and mod. 36 ripper
Who is online
Users browsing this forum: No registered users and 20 guests