From the testing:
Liquid Wrench ... 127 pounds .. $0.21
Kano Kroil ........ 106 pounds .. $0.75
This means that Kano Kroil is less than 20% more effective, but cost OVER 3.5 times as much as Liquid Wrench.
Until I can no longer find "21 more pounds" of force, I will save my money.
Penetrating fluids
- JD440ICD2006
- 350 crawler
- Posts: 1113
- Joined: Tue Aug 22, 2006 3:57 pm
- Location: South Carolina
I bought a gallon of Kroil directly from Kano Labs over the internet. It works pretty good, I have gotten one stuck Minne-moline loosened using it. It does a number on Harbor Freight oil cans though, apparently all the O-Rings in the pump plunger swell badly. LOL
Bryce
Bryce
No trees were hurt in the creation of this message.
But, many electrons were terribly bothered.
440IC/602, 2-440ICD/831 MM UBU-LP, 445N-LP, 445E-LP, BIG MO 400-M, 4 Star-LP M5-D, M5-LP, M602-LP, M670-LP, G900-LP, G900-D, G1000 Vista-LP Case 580CK
But, many electrons were terribly bothered.
440IC/602, 2-440ICD/831 MM UBU-LP, 445N-LP, 445E-LP, BIG MO 400-M, 4 Star-LP M5-D, M5-LP, M602-LP, M670-LP, G900-LP, G900-D, G1000 Vista-LP Case 580CK
Joe , thanks for the link to Kano Lab's , I need to order a gallon here soon . The crawler used quite a bit of it last year during the tear down
Dan
Dan
1956 420C with GSC blade
Tools are to men as shoes are to women , you can never have too many !!
Used diesel engines are an adventure any way you look at them !!
Tools are to men as shoes are to women , you can never have too many !!
Used diesel engines are an adventure any way you look at them !!
- JD440ICD2006
- 350 crawler
- Posts: 1113
- Joined: Tue Aug 22, 2006 3:57 pm
- Location: South Carolina
I agree, if they are weakened and/or not ready to break lose, they can snap off. In these cases, it really does not matter what you have used.
Exhaust bolts are a good example. They get pitted and it makes that area weaker.
When this happens, the "trick" penetrating oils and water take a back seat to some welding skills and more patience. Or, some drilling skills and a good set of easy outs.
Exhaust bolts are a good example. They get pitted and it makes that area weaker.
When this happens, the "trick" penetrating oils and water take a back seat to some welding skills and more patience. Or, some drilling skills and a good set of easy outs.
1959 JD 440ICD w/64 Power Angle Tilt Blade
1959 JD 440ICD w/63 Manual Angle Blade
1959 JD 440IC w/602 Manual Angle Blade
1959 JD 730D W SE (many options)
1950 JD M S w/M-20 Mower
1952 JD M W
1955 FORD 640 (burns the most fuel)
1959 JD 440ICD w/63 Manual Angle Blade
1959 JD 440IC w/602 Manual Angle Blade
1959 JD 730D W SE (many options)
1950 JD M S w/M-20 Mower
1952 JD M W
1955 FORD 640 (burns the most fuel)
One thing I have noticed frequently over the years is the benefit of vibration. Often times a bolt will break off if you are using hand tools, but the vibration of an impact wrench will tend to braek up the tension of the rust and often times they will come right out.
Also, the best penetrant I have ever used is heat. Heat the surrounding area to glowing if you can, and usually they will come right out.
Lavoy
Also, the best penetrant I have ever used is heat. Heat the surrounding area to glowing if you can, and usually they will come right out.
Lavoy
Who is online
Users browsing this forum: No registered users and 78 guests