General help and support for your Lindeman through 2010 John Deere crawler
-
Stan Disbrow
- 350 crawler
- Posts: 2898
- Joined: Fri Jul 15, 2005 3:13 pm
- Location: Raleigh, NC
Post
by Stan Disbrow » Sat Feb 15, 2014 11:30 am
gregjo1948 wrote:Hey Stan--If you're adding a velocity stack, you might as well install racing slicks!
gregjo1948
Hi,
I saw a 420c with the rubber blocks on the pads doing a tractor pull. Off one of the recent Yoo Toob links, I think. So, for a crawler I think those are slicks!
Stan
There's No Such Thing As A Cheap Crawler!
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
-
original possum
- 1010 crawler
- Posts: 258
- Joined: Wed Sep 11, 2013 3:34 pm
- Location: Shiner, texas
Post
by original possum » Sat Feb 15, 2014 3:15 pm
Lavoy is right again! Turns out the 40C was burned and rewired by my electrical engineer brother while I was away in the Army. He added the resistor to save the points, but when I changed the coil it had to go. And he used all red wire.
Early 40C w/Yakima toolbar and homebuilt ripper: 350 w/6-way
-
Stan Disbrow
- 350 crawler
- Posts: 2898
- Joined: Fri Jul 15, 2005 3:13 pm
- Location: Raleigh, NC
Post
by Stan Disbrow » Sat Feb 15, 2014 5:13 pm
Hi,
Ah ha! All red wire is fine, if you use Brady wire marking tags on them all to figure out which go where....
As far as electrical engineering goes, they skipped Ignition Systems 101 when I was learning it. I got my schooling in that field way earlier.
Stan
There's No Such Thing As A Cheap Crawler!
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
-
Paul Buhler
- 350 crawler
- Posts: 991
- Joined: Wed May 21, 2008 6:25 pm
- Location: Killington, VT
Post
by Paul Buhler » Sat Feb 15, 2014 5:34 pm
I got my schooling in that field way earlier.
Me too. -- "Hold that plug near the hole while I crank the engine over. Let's see if there's any spark"; no rag, no glove, no joy.
Paul Buhler
Killington, VT
420c 5 roll with 62 blade, FOPS, and Gearmatic 8a winch
-
gregjo1948
- 350 crawler
- Posts: 1000
- Joined: Mon Aug 30, 2010 5:58 am
- Location: Newark Valley,NY,USA
Post
by gregjo1948 » Mon Feb 17, 2014 6:28 am
Paul-- There might be a little humor in the plug holding, if you're not the holder.
gregjo1948
JD 350B diesel 6way blade, Case 580B Loader/backhoe, Farmall 504 high crop w/ flail boom mower, International 404 , International 284 diesel w/belly mower, 1972 Ford F600 dump truck, Galion 3-5 roller, Allis Chalmers D17, 1620 Ford
Who is online
Users browsing this forum: No registered users and 161 guests