Off to look at this 1010. Gas.
Off to look at this 1010. Gas.
I am a bit worries about that sprocket rubbing on the roller.
gas engine
It is a long drive so I will take the trailer.
450`s c-dozer 6 way, b-loader.
350`s c-loader + ripper, b-loader with winch arch. B-loader with dozer pads
backhoe attachment.
1010 loader with forks for round bales
a few 610 Bobcats. many attachments
350`s c-loader + ripper, b-loader with winch arch. B-loader with dozer pads
backhoe attachment.
1010 loader with forks for round bales
a few 610 Bobcats. many attachments
-
- 2010 crawler
- Posts: 622
- Joined: Tue Mar 30, 2010 8:02 am
- Location: Steubenville, OH
Looks like a pretty decent machine. If it's a one owner then it's definitely been taken care of.
The sprocket rubbing could be out of adjust or bearing going out.
Question: Is that the original decal on the back of the seat? Reason I ask is because that decal is on the back of my 440. I've never seen another 440 with it though so now I'm thinking that the decal is for a 1010.
The sprocket rubbing could be out of adjust or bearing going out.
Question: Is that the original decal on the back of the seat? Reason I ask is because that decal is on the back of my 440. I've never seen another 440 with it though so now I'm thinking that the decal is for a 1010.
Ben
Great Grandpa's 1960 440ICD 602 blade
Between SN's: 455,633 - 456,801
Currently Rebuilding/Restoring
Great Grandpa's 1960 440ICD 602 blade
Between SN's: 455,633 - 456,801
Currently Rebuilding/Restoring
If the sprocket is hitting the roller, assume full rebuild on the final drive.
Lavoy
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator www.jdcrawlers.com
Owner and moderator www.jdcrawlers.com
-
- 1010 crawler
- Posts: 305
- Joined: Mon Apr 04, 2005 7:01 pm
- Location: Gloucester,Virginia
Decal
Ben,
My 440 loader has the same decal on the back of it's seat.It is just
much lower down.I always thought it was original but like you never have seen it another 440.Luck,JimAnderson
My 440 loader has the same decal on the back of it's seat.It is just
much lower down.I always thought it was original but like you never have seen it another 440.Luck,JimAnderson
I have a parts 1010 diesel loader that runs and my friend is using it to feed horses. It smokes and misses (either damage) and has a poor final on the left side. I know about the final because the drain plug on the bottom has the square stripped out so I took it off to check the oil. Dry in there and the big gear is wobbly. otherwise it still works and you do not notice anything when operating it. Put oil in and he uses it a couple hours a winter. However, it has a brand new complete original undercarriage. I am thinking of moving all the best parts to the dozer, and putting the rest in the parts pile. A question....I have a parts 350 loader with brand new chains and dozer pads, will the pads fit the 1010 ? I thought I read somewhere that they do, but can not recall. Not sure if a 1010 is really worth the effort, I was looking for a 350 dozer to use them on when I came across this 1010. It is a nice looking 1010 in the picks. 10 hour round trip to get it but, good roads all the way.
-
- 2010 crawler
- Posts: 597
- Joined: Thu Aug 27, 2009 10:08 pm
- Location: Edmonton, Alberta
Trade into Alberta For a 440
Just bring some of those non-runners over the border here to Alberta, I might a have 440 IC loader that could use a new home.
You must be up to 10 Deeres already!!
You must be up to 10 Deeres already!!
Jason Benesch
John Deere 420, 430, 440 & 350C With 3 Point Hitch
John Deere 400G With Winch
John Deere 2010 Crawler Dozer
John Deere 420, 430, 435 & 440 Wheel Tractors
John Deere 420, 430, 440 & 350C With 3 Point Hitch
John Deere 400G With Winch
John Deere 2010 Crawler Dozer
John Deere 420, 430, 435 & 440 Wheel Tractors
I got to 10 a while back and decided that is good enough for my hobby. Then I got busy with work and such. But that was the plan, collect a few then they can wait until I have more time to fix. I have used that winch crawler a lot, it has been a blessing with the forest and all. Using the now converted 450 dozer more including this weekend as. I have big brush piles to burn before the RM closes the fire season on April 1st. I am hoping the 3 feet of snow on them (I cleared the front away with the skid steer) won't keep them from burning completely.. The 2 piles are about 12 feet high and 16 deep by 50 long so once they get going there will be some heat there. Burned a few early on before the snow was deep and it went ok.
Also hope to get out for a short sled as we have lots of snow yet. Friends are coming up and they will put on lots of kms on the trails but, for me, I am weary of trail riding and mostly go for the powder. Now we have a thick crust on top where it is deep and last time out I wore the side decals clean off my MTX Nytro doing turns getting stuck(thank you bungee) and having fun. |this weekend I will stay home and tend the fires, and get in a little Deere time.
I an not ruling out sending this pile of iron out to Alberta if I cant get it inside before too long, my wife would let out a cheer for sure.
I am flush with loaders, plus my collection of Bobcats so, not anxious to get another. The only thing I have been selling is skid steer grapples, buy them at Richies and sell on Kijiji. Picking up 8 tomorrow from the sale earlier this week. Seems like everyone needs one.
Also hope to get out for a short sled as we have lots of snow yet. Friends are coming up and they will put on lots of kms on the trails but, for me, I am weary of trail riding and mostly go for the powder. Now we have a thick crust on top where it is deep and last time out I wore the side decals clean off my MTX Nytro doing turns getting stuck(thank you bungee) and having fun. |this weekend I will stay home and tend the fires, and get in a little Deere time.
I an not ruling out sending this pile of iron out to Alberta if I cant get it inside before too long, my wife would let out a cheer for sure.
I am flush with loaders, plus my collection of Bobcats so, not anxious to get another. The only thing I have been selling is skid steer grapples, buy them at Richies and sell on Kijiji. Picking up 8 tomorrow from the sale earlier this week. Seems like everyone needs one.
-
- 2010 crawler
- Posts: 622
- Joined: Tue Mar 30, 2010 8:02 am
- Location: Steubenville, OH
Re: Decal
Well I guess there's me and you for sure. I can't figure my grandpa or great grandpa would've ever wasted money on a decal, so I figure the stuff on mine was original. Hard to tell though.JimAnderson wrote:Ben,
My 440 loader has the same decal on the back of it's seat.It is just
much lower down.I always thought it was original but like you never have seen it another 440.Luck,JimAnderson
Mine also had the word DIESEL above 440 on the front plates, but I think that may be wrong, that's how it was when I got all the parts though.
Ben
Great Grandpa's 1960 440ICD 602 blade
Between SN's: 455,633 - 456,801
Currently Rebuilding/Restoring
Great Grandpa's 1960 440ICD 602 blade
Between SN's: 455,633 - 456,801
Currently Rebuilding/Restoring
Who is online
Users browsing this forum: No registered users and 53 guests