Tracks
-
- 420 crawler
- Posts: 43
- Joined: Tue Nov 30, 2010 4:56 pm
Re: Tracks
So are you saying 3 point from factory was not available for a 40c period ? and if there is one present that's for sure factory components these were removed from a 420c ?
50 MC 11526
50 MC 12103
50 MC 12147
52 MC 15855
52 MC 18039
53 40C 61623 (3) roller
54 40C 62435 ALL FUEL (4) roller 3 point hitch
55 40C 70680 (5) roller 3 point hitch
50 MC 12103
50 MC 12147
52 MC 15855
52 MC 18039
53 40C 61623 (3) roller
54 40C 62435 ALL FUEL (4) roller 3 point hitch
55 40C 70680 (5) roller 3 point hitch
Re: Tracks
I think you posted this to the wrong thread - did you intend for it to be with your thread "430C 3 Point+blade" down below?
-
- 420 crawler
- Posts: 43
- Joined: Tue Nov 30, 2010 4:56 pm
Re: Tracks
no earlier on in this thread there is discussion of 3 point
50 MC 11526
50 MC 12103
50 MC 12147
52 MC 15855
52 MC 18039
53 40C 61623 (3) roller
54 40C 62435 ALL FUEL (4) roller 3 point hitch
55 40C 70680 (5) roller 3 point hitch
50 MC 12103
50 MC 12147
52 MC 15855
52 MC 18039
53 40C 61623 (3) roller
54 40C 62435 ALL FUEL (4) roller 3 point hitch
55 40C 70680 (5) roller 3 point hitch
Re: Tracks
Sorry, I missed that. You might try leaving a PM for JimAnderson, if you are looking to see if he has more info. It looks like he was on the site back in October. Good luck.
Jim
Jim
- Paul Buhler
- 350 crawler
- Posts: 991
- Joined: Wed May 21, 2008 6:25 pm
- Location: Killington, VT
Re: Tracks
Jim Anderson: Wishing you all the best. Happy Holidays. Every time I run my 420, I think of your helpful comments as I brought it to a better level of reliability. Fired it up yesterday; two cranks, and runs like a top. Steers and pushes well. I need to go back into my winch and adjust the clutch a bit tighter, but a quick fix and minor annoyance at worst. Paul
Paul Buhler
Killington, VT
420c 5 roll with 62 blade, FOPS, and Gearmatic 8a winch
Killington, VT
420c 5 roll with 62 blade, FOPS, and Gearmatic 8a winch
Re: Tracks
40s never left the factory with a 3 point.
There were 3 point "bundles" that could be purchased once the 420s came out, and one of those bundles could be installed on 4 and 5 roller 40 crawlers.
Lavoy
There were 3 point "bundles" that could be purchased once the 420s came out, and one of those bundles could be installed on 4 and 5 roller 40 crawlers.
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator www.jdcrawlers.com
Owner and moderator www.jdcrawlers.com
-
- 420 crawler
- Posts: 43
- Joined: Tue Nov 30, 2010 4:56 pm
Re: Tracks
why not 3 roller 40's ?
50 MC 11526
50 MC 12103
50 MC 12147
52 MC 15855
52 MC 18039
53 40C 61623 (3) roller
54 40C 62435 ALL FUEL (4) roller 3 point hitch
55 40C 70680 (5) roller 3 point hitch
50 MC 12103
50 MC 12147
52 MC 15855
52 MC 18039
53 40C 61623 (3) roller
54 40C 62435 ALL FUEL (4) roller 3 point hitch
55 40C 70680 (5) roller 3 point hitch
- Stan Disbrow
- 350 crawler
- Posts: 2904
- Joined: Fri Jul 15, 2005 3:13 pm
- Location: Raleigh, NC
Re: Tracks
Hi,
Not enough track length for the down pressure of the 3 pt I think. As the implement is shoved into the ground, force is transferred towards the front. I think too much for the front idler on a 3 roller wihout another roller or two to share that load.
Stan
Not enough track length for the down pressure of the 3 pt I think. As the implement is shoved into the ground, force is transferred towards the front. I think too much for the front idler on a 3 roller wihout another roller or two to share that load.
Stan
There's No Such Thing As A Cheap Crawler!
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
Useta Have: '58 JD 420c 5-roller w/62 inside blade
Useta Have: '78 JD350C w/6310 outside blade
Useta Have: '68 JD350, '51 Terratrac GT-25
Have: 1950 M, 2005 x495, 2008 5103 (now known as 5045D)
Re: Tracks
3 roller 40 has a different rear trans cover that will not accept the rockshaft support piece, and it can not be changed due to the style of PTO.
Lavoy
Lavoy
Parts and restoration for antique and late model John Deere crawlers.
Owner and moderator www.jdcrawlers.com
Owner and moderator www.jdcrawlers.com
Who is online
Users browsing this forum: No registered users and 14 guests