1956 420c for trade
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
1956 420c for trade
1956 JD 420c for sale or trade. It has a 6 way blade. The right hand side does not turn as easily as the left. The adjustment for both sides on the brakes is maxed out. I have the materials for the brakes and the rivets, I just dont want to do the job. LOL (I have done it before)
The pins and bushings have minimal wear on them, maybe a eigth of an inch into the bushing. Engine runs strong and it will work if you want it to. There is a sand pit next door if you want to try it out. Every one needs a sand pile to play in, grin.
What I would like to find is a rubber tired tractor that I can use for a people mover during the fairs or something near equivelant value. I would like to sell this at the appraised value of $4500 (or trade).
The pins and bushings have minimal wear on them, maybe a eigth of an inch into the bushing. Engine runs strong and it will work if you want it to. There is a sand pit next door if you want to try it out. Every one needs a sand pile to play in, grin.
What I would like to find is a rubber tired tractor that I can use for a people mover during the fairs or something near equivelant value. I would like to sell this at the appraised value of $4500 (or trade).
Last edited by Willyr on Sun Feb 19, 2012 1:28 pm, edited 4 times in total.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
deleted info
Last edited by Willyr on Wed Feb 08, 2012 7:56 pm, edited 1 time in total.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
deleted info
Last edited by Willyr on Wed Feb 08, 2012 7:56 pm, edited 1 time in total.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
Well I had a nibble today for a 520? Can anyone give me details (size weight) on a 520?
Last edited by Willyr on Wed Mar 21, 2012 11:13 pm, edited 1 time in total.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
I am really surprised no one on this board cares for this deal. Sigh oh well.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- steamfitter99
- 430 crawler
- Posts: 72
- Joined: Thu Nov 10, 2005 10:30 pm
- Location: Central Illinois
crawler for sale
I'm interested, but Maine is just a little too far. I have my eye on 2 in Wisconsin right now. I think it would be a good deal. Tom.
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
So some one from this board contacted me yesterday, he told the fellow that I was going to do the trade with that my tractor needed pins and bushings. Upon his thoughts he said it was a two thousand dollars for clutch repair.
Granted it needs steering brakes, sure it would be a good idea to replace the clutches at the same time. Yet "Eric" told him he would have to spend more than the cost of the tractor to do this.
I saw a sign in Radio Shack that is most fitting. Samson slew a thousand Philistines with the jawbone of an ass. The same weapon was used by some one yesterday that killed the trade for the tractor. Grrrrr.
Granted it needs steering brakes, sure it would be a good idea to replace the clutches at the same time. Yet "Eric" told him he would have to spend more than the cost of the tractor to do this.
I saw a sign in Radio Shack that is most fitting. Samson slew a thousand Philistines with the jawbone of an ass. The same weapon was used by some one yesterday that killed the trade for the tractor. Grrrrr.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Eric.MacLeod
- 440 crawler
- Posts: 120
- Joined: Sun Feb 10, 2008 9:15 pm
- Location: wells,maine
hello willyr, i hope someone isnt using my name to bad mouth your dozer. you can buy both sides to redo the brakes and clutches for about a 1000$. and i dont know how someone that has never seen your dozer can assume that the pins and bushings would be gone. i know the economy is bad but i would think someone would jump at that deal.uncle henrys or craigslist has alot of views each week.good luck..Eric.
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
Apology accepted.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
delivery is possible after purchase
I would need to be compensated for diesel and tolls if incurred.
I would need to be compensated for diesel and tolls if incurred.
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
Ok, so I found a JD B. Alas he wont trade, he will if I sell mine take cash. So, if anyone wants, my tractor at 3k
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
- Willyr
- 2010 crawler
- Posts: 695
- Joined: Sat Jul 17, 2010 3:03 am
- Location: Downeast Maine (North of Ellsworth)
Lavoy or any moderator, please delete this thread. I have traded for a John Deere 60
former owner of a 1956 420c
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
All help is greatly appreciated.
Proud owner of a project 1952 JD 60
http://www.youtube.com/watch?v=nFehqXVd9z4
Who is online
Users browsing this forum: No registered users and 61 guests